Neumann KM185 Hypercardioid Miniature Microphone Stereo Set

(No reviews yet) Write a Review
SKU:
KM185 STEREOSET
UPC:
615104085268
Weight:
2.50 LBS
Shipping:
Calculated at Checkout
  • Neumann KM185 Hypercardioid Miniature Microphone Stereo Set
  • Neumann KM185 Hypercardioid Miniature Microphone Stereo Set
  • Neumann KM185 Hypercardioid Miniature Microphone Stereo Set
$1,650.00

Description

The Neumann SKM 185 is stereo set of two KM 185 Hypercardioid Miniature Microphones, two SG 21 BK Stand Mounts and two WNS 100 Windscreens in a woodbox.

Because of KM 185's optimized mechanical construction and conscious omission of modularity, which is unnecessary in many cases, the KM 185 is predestined for economy-minded production and home recording studios.

The KM 183 omnidirectional and KM 185 hypercardioid microphones are based on the tremendously successful KM 184 cardioid microphone, which has become a standard within the global studio community in just a very short time. The KM 184 microphone is available with either Matte Black or Nickel finish with transformerless circuitry.

Applications

Their slender shapes and the transmission characteristics described below make the "Series 180" especially suitable for a very wide range of tasks in the radio and television sector.

  • Ideal as AB stereo pair because of the flat frequency response in the diffuse sound field
  • As a main mic, especially for capturing room acoustics
  • For stereo recordings with a baffle plate
  • As a spot mic for piano, wind instruments, organ, choir

Acoustic Features

The KM 185 with its hypercardioid characteristic features attenuation of sound incidence from the side or rear of about 10 dB, with minimum sensitivity at an angle of 120°.

Electrical Features

The KM 185 microphone has the same transformerless circuitry as is used in the KM 100 system, resulting in excellent technical specifications: Compared to the KM 84 the dynamic range of the KM 184 increased by 24 dB mainly through the reduction of self-noise level to only 22 dB (CCIR) and an increased sound pressure handlingcapability of up to 138 dB. The microphone operates without any problems, even if the input of following equipment happens to be unbalanced, for example as in some DAT recorders. The output of the KM 185, as in all Neumann microphones, is balanced and phantom (48V) powered.

Economy

The KM 185 is a good choice for all users who look for a high-quality miniature microphone, but do not need the complex, modular KM 100 system, which continues to be part of the Neumann product range.

The mechanical construction was simplified, for example, capsule and output stage cannot be separated from each other. For this reason the KM 185 is an economical alternative without giving up the electroacoustic features the users expect from Neumann microphones.

SG 21 Bk Stand Mount

Swivel mount with a plastic clamp for miniature microphones. It has a 5/8"-27 female thread, plus a thread adapter to connect to 1/2"- and 3/8" stands.

WNS 100 Windscreen

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available. Typically, they are made out of open-cell polyurethane foam. These windscreens do not cause interfering resonances and do not influence the directional pattern. Only in the upper frequency range is the output level slightly attenuated. The wind noise attenuation was measured without electrical filtering in a turbulent air stream traveling at 20 km/h, generated by a noiseless wind machine.

  • Wind noise attenuation 18 dB
  • Attenuation at 15 kHz 2 dB. Ø 45 mm
View AllClose

Specifications

Acoustical operating principle Pressure/Pressure gradient transducer
Directional pattern Hypercardioid
Frequency range 20 Hz ... 20 kHz
Sensitivity at 1 kHz into 1 kohm 10 mV/Pa
Rated impedance 50 ohms
Rated load impedance 1 kohms
Equivalent noise level, CCIR 24 dB
Equivalent noise level, A-weighted 15 dB-A
Signal-to-noise ratio, CCIR (rel. 94 dB SPL) 70 dB
Signal-to-noise ratio, A-weighted (rel. 94 dB SPL) 79 dB
Maximum SPL for THD 0.5% 142 dB
Maximum output voltage 10 dBu
Supply voltage (P48, IEC 61938) 48 V ± 4 V
Current consumption (P48, IEC 61938) 3.2 mA
Matching connectors XLR 3F
Weight approx. 80 g
Diameter 22 mm
Length 107 mm

View AllClose

0 Reviews

View AllClose